P6IPA Intel®
815EP & 82801BA Chipset Sockets
370 for Celeron™ FC-PGA processors 533A, 566 & >566MHz
(66MHz FSB), FC-PGA Pentium®
III processors (100/133MHz FSB) Three
168-pin DIMMs with SDRAM support, up to 768GB ITE
LPC I/O - IT8712F AC97
Audio Codec
P6IPA mainboard
is an ATX mainboard that uses a 4-layer printed
circuit mainboard and measures 305 mm x 220 mm. The mainboard has a Socket
370 for FC-PGA Intel® Celeron™ or FC-PGA
Pentium® III processors that support frontside bus (FSB)
speeds up to 133 MHz. The mainboard is installed with the Intel®
815EP chipset. The mainboard delivers high-level performance with
a 4xAGP (Ac-celerated Graphics Port) slot and two Bus Master Ultra DMA (UDMA)
ports that support up to four ATAPI (AT Attachment Packet Interface) devices.
The PCI IDE also supports PIO Mode 3 and 4, UDMA33/66/100
IDE, and an ATAPI CD-ROM. The mainboard ac-commodates
PC 100 and PC 133 SDRAM (Synchronous DRAM) up to 768 MB using three 3.3V
unbuffered DIMM modules.
The mainboard includes an AC 97 audio codec. There is a full set of I/O
ports, such as dual channel IDE interfaces, a floppy interface, one FIFO
serial port connector, one VGA port, an EPP/ECP-capable bi-directional parallel
port connector, a dual USB (Universal Serial Bus) connector, and PS/2 keyboard
and mouse connectors.
Two extra USB ports can be added using an extended USB module that connects
to the mainboard. An extra COM port can be connected using an extension
bracket.
One AGP slot, six PCI local bus slots, and a CNR (Communica-tions Networking
Riser) provide expandability for add-in expansion cards.
PROCESSORS
Celeron™ FC-PGA processorsup to 766MHz(66MHz FSB) and up to 800MHz(100MHz FSB)
Intel® FC-PGA Pentium®
III processors up to 850MHz(100MHz FSB) and 1GBz(133MHz FSB)
Cyrix® III processors up to 600MHz(100MHz FSB) and up to
667MHz(133MHz)
Cyrix® III-2(64K cache) processors up to 650MHz(100MHz FSB)
and up to 667MHz(133MHz)
Three
168-pin DIMMsockets for 3.3V SDRAM (Ready for
PC100, PC133) Maximum: 768MB
SYSTEM BIOS
Award
BIOSwith Flash ROM in Firmware Hub (FWH) Supports Plug and Play
1.0A, AMP 1.2, Multi Boot, DMI Full support for ACPI
revision 1.0A specification
I/O INTERFACE
Supports Plug and Play function PS/2 keyboard and PS/2
mouse connectors Four USB Ports (Two USB
Connectors as header on board) One - EPP/ECP mode parallel
port Two - 16550 high-speed
serial I/O ports Audio Ports (Line-in,
Line-out, Mic-in, CD-in and game port) Supports 360K~2.88M Byte,
3 Mode FDDs or LS120 Dual PCI IDE interfaces
- support four IDE devices (PIO mode 4, DMA Mode 2, Ultra DMA 33/66/100) ATX Power Supply Connector Ports, headers and others: IrDA header Extra (Front Panel) MIC
/ Line-Out header Chassis open detector header Green, HDD, Power indicator
LED headers CPU and Case Fan headers
LAN Card Wake Up / Internal
Modem Ring Wake-Up headers
RTC & BATTERY
Intel I/O
Controller Hub 2 (ICH2) included 256 bytes of CMOS SRAM With CMOS SRAM hardware
clear jumper
Intel®
815EP & 82801BA Chipset
& Firmware Hub (FWH)
with following features: 
IrDA header